Kode Error Canon MP258

Printer seri Canon MP258 merupakan kelanjutan dari seri printer multifungsi MP145 dan MP198. Sementara yang terbaru saat ini adalah MP287. Printer seri MP258 ini sudah tidak keluar lagi namun demikian unit-unit lama tentu masih banyak dipakai di kantor-kantor dan rumah. Printer baru saja kadang rusak apalagi printer lama seperi MP 258 ini. Jika rusak kode errornya akan muncul di LCD.
Berikut ini beberapa kode error yang bisa dijumpai pada MP258
(sumber artikel dari http://jogjaprint.blogspot.com/2011/10/kode-error-printer-canon-mp-258-dan.html)

P02 (Carriage error): Make sure no foreign material stuck to the print head railway.
Clean and check the print head encoder strip cable (timing slit film or encoder strip is a white line on the back of the box set of ink lines may be missing or mess up the ink.

P03 (Line feed error): an error in transmission line entering the line feed (LF) is a signal telling the printer to move to another line or a whole new line that would not otherwise have reached the end of the line.Check wire print head position (timing slit disk film) on the side of the machine. Check PCB logic board.

P05 (ASF sensor error) sensor for paper feed error. Try to replace the following: ASF / PE sensor unit, Drive unit, PCB logic board.

P06 (Internal temperature error): caused by abnormal heat inside the printer.

P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full. Replace the wastepad inside the printer or install waste ink bin outside the printer then reset counter protection.

P08 (Print head temperature rise error): caused by thermal print head temperature exceeds a threshold. Replace the new cartridge print head and / or change a new logic board.

P09 (EEPROM error): caused by corrupted or defective EEPROM chips of the printer. Replace the logic board.

P15 (USB VBUS over current): caused by too much current, try removing the USB cable and then plugin again, if solve the error, try to replace with a new USB cable. If the error still exist replace the logic board.

P20 (Other hardware error): The failure of other hardware. Try to replace the logic board.

P22 (Scanner error): a scanner malfunction. Try to change the scanner unit or change a the logic board.

E13 or E16: Ink has run out. Pressing the Stop / Reset button for 5 to 8 seconds until the led screen display number 1.

E04, E05, E14 or E15: Cartridge may not be installed properly. Reinstall the ink cartridge.

Kode Error Canon MP Series dengan Huruf 'E'

-------------------------------------------------------------

E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16-E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error